24VDC Starter 12V 200A 150A Truck Car Relays
Features：
● A set of bridge contact points
● 150A switching capability
● plastic sealed
● Outline dimensions: 33.5X52.4X65
● Working temperature as high as 75 °C
Specification
| Contact Form | 1 A One set of bridge |
| Maximum continuous | 150A |
| Max.Operating Voltage | 110VDC |
| Electrical durability | 5×104times |
| Mechanical Durability | 1×107times 300 times/minute |
| Insulation Resistance | 20MΩ |
| Operate/Release | 50ms or less |
| Release Time | 50ms or less |
| Operating temperature | -40℃~+75℃ |
| Vibration | 10Hz~500Hz，5.0G |
| Package mode | Plastic seal |
Contact parameter
| Contact load voltage | Load type | Contact load voltage A | On-off ratio | Electrical durability | Contact material | Test environment temperature | Contact wiring diagram | ||
| bridging（1A） | Turn on S | Turn off S | |||||||
| 14VDC | Resistive | Turn on | 150 | 1 | 4 | 5×104次 | Agsno2In2o3 | 23℃ | see picture 1 |
| Turn off | 150 | 1 | 4 | 5×104次 | Agsno2In2o3 | 23℃ | see picture 1 | ||
| 28VDC | Resistive | Turn on | 100 | 1 | 4 | 5×104次 | Agsno2In2o3 | 23℃ | see picture 1 |
| Turn off | 100 | 1 | 4 | 5×104次 | Agsno2In2o3 | 23℃ | see picture 1 | ||
| 72VDC | Resistive | Turn on | 50 | 1 | 4 | 5×104次 | Agsno2In2o3 | 23℃ | see picture 1 |
| Turn off | 50 | 1 | 4 | 5×104次 | Agsno2In2o3 | 23℃ | see picture 1 | ||
| 110VDC | Resistive | Turn on | 30 | 1 | 4 | 5×104次 | Agsno2In2o3 | 23℃ | see picture 1 |
| Turn off | 30 | 1 | 4 | 5×104次 | Agsno2In2o3 | 23℃ | see picture 1 | ||
Coil Ratings
| Standard | Normal voltage (VDC) | Pick-up voltage (VDC) | Drop-out voltage (VDC) | Coil resistace (Q±10%) | Parallel resistance (Q±5%) | Equivalent resistance (Q±10%) | Power consumption (W) | Max.allowable overdrive voltage1) (VDC) | |
| 20 °C | 85 °C | ||||||||
| 12 | 8.4 | 1.2 | 90 | - | - | 1.6 | 20.2 | 15.7 | |
| 12 | 8.4 | 1.2 | 80 | 680 | 79.5 | 1.8 | 20.2 | 15.7 | |
| 24 | 16.8 | 2.4 | 360 | - | - | 1.6 | 40.5 | 31.5 | |
| 24 | 16.8 | 2.4 | 320 | 2700 | 317.6 | 1.8 | 40.5 | 31.5 | |
ORDERING GUIDE
EXTERNAL DIMENSIONS
Remark:
（1）In case of no tolerance shown in outline dimension: outline dimension≤1mm, tolerance should be ±0.2mm;
Outline dimension＞1mm and≤5mm, tolerance should be ±0.3mm; outline dimension＞5mm,
tolerance should be ±0.4mm.
